High-Temperature Performance of Ultra-High-Performance Concrete Incorporating Iron Tailings Sand and Steel Slag Powder
DOI:
https://doi.org/10.54691/k0gyze85Keywords:
Ultra-high-performance Concrete; Iron Tailings Sand; Steel Slag Powder; Hybrid Fibers.Abstract
Ultra-high-performance concrete (UHPC) incorporating iron tailings sand and steel slag powder was prepared to investigate the effects of steel–polypropylene (PP) fiber proportions on flowability, ambient mechanical properties, and post-heating residual strength. The total fiber volume fraction was maintained at 2.0%, with PP fiber volume fractions of 0, 0.3%, 0.6%, and 0.9%. The steel-fiber mixture and the mixture containing 1.7% steel fibers and 0.3% PP fibers were selected for exposure to 200, 400, 600, and 800 °C at a heating rate of 4 °C/min, followed by a 2 h holding period and natural cooling. Increasing the PP fiber fraction reduced the flow spread from 489 to 442 mm. The mixture containing 0.3% PP fibers largely retained its ambient strength, with 28-day compressive and flexural strengths of 117.3 and 19.7 MPa, respectively. Both selected mixtures exhibited their highest residual strengths at the tested temperature of 200 °C, followed by strength reductions at higher temperatures. The steel-fiber specimens lost structural integrity after exposure to 600 °C, whereas the PP-containing specimens remained intact without thermal spalling at 600 and 800 °C. Nevertheless, their residual compressive and flexural strengths decreased to 19.8 and 3.9 MPa, respectively, at 800 °C. These results show that specimen integrity and residual load-bearing capacity must be evaluated separately when selecting fiber combinations for heat-exposed UHPC.
Downloads
References
[1] Richard, P., & Cheyrezy, M. (1995). Composition of reactive powder concretes. Cement and Concrete Research, 25(7), 1501–1511. https://doi.org/10.1016/0008-8846(95)00144-2.
[2] Sharma, R., Jang, J. G., & Bansal, P. P. (2022). A comprehensive review on effects of mineral admixtures and fibers on engineering properties of ultra-high-performance concrete. Journal of Building Engineering, 45, 103314. https://doi.org/10.1016/j.jobe.2021.103314.
[3] Zhao, S., Fan, J., & Sun, W. (2014). Utilization of iron ore tailings as fine aggregate in ultra-high performance concrete. Construction and Building Materials, 50, 540–548. https://doi.org/10.1016/j.conbuildmat.2013.10.019.
[4] Zhang, W., Gu, X., Qiu, J., Liu, J., Zhao, Y., & Li, X. (2020). Effects of iron ore tailings on the compressive strength and permeability of ultra high performance concrete. Construction and Building Materials, 260, 119917. https://doi.org/10.1016/j.conbuildmat.2020.119917.
[5] Li, S., Cheng, S., Mo, L., & Deng, M. (2020). Effects of Steel Slag Powder and Expansive Agent on the Properties of Ultra-High Performance Concrete (UHPC): Based on a Case Study. Materials, 13(3), 683. https://doi.org/10.3390/ma13030683.
[6] Piao, R., Kim, S. J., Na, Y. K., Lee, N., & Yoon, Y. S. (2025). Optimization of cement replacement with steel slag powder in ultra-high-performance concrete: Microstructural evolution and mechanical performance. Construction and Building Materials, 492, 142862. https://doi.org/10.1016/j.conbuildmat.2025.142862.
[7] Zhang, D., Dasari, A., & Tan, K. H. (2018). On the mechanism of prevention of explosive spalling in ultra-high performance concrete with polymer fibers. Cement and Concrete Research, 113, 169–177. https://doi.org/10.1016/j.cemconres.2018.08.012.
[8] Li, Y., Tan, K. H., & Yang, E. H. (2019). Synergistic effects of hybrid polypropylene and steel fibers on explosive spalling prevention of ultra-high performance concrete at elevated temperature. Cement and Concrete Composites, 96, 174–181. https://doi.org/10.1016/j.cemconcomp.2019.02.016.
[9] Li, Y., Zhang, Y., Yang, E. H., & Tan, K. H. (2019). Effects of geometry and fraction of polypropylene fibers on permeability of ultra-high performance concrete after heat exposure. Cement and Concrete Research, 116, 168–178. https://doi.org/10.1016/j.cemconres.2018.11.009.
[10] Li, Y., Yang, E. H., & Tan, K. H. (2020). Flexural behavior of ultra-high performance hybrid fiber reinforced concrete at the ambient and elevated temperature. Construction and Building Materials, 250, 118487. https://doi.org/10.1016/j.conbuildmat.2020.118487.
[11] Lin, J., Zhang, Y., Huang, S., Wang, Y., & Zhang, Z. (2024). Influence of synthetic fibers on the performance of ultra-high performance concrete (UHPC) at elevated temperatures. Journal of Building Engineering, 97, 110735. https://doi.org/10.1016/j.jobe.2024.110735.
[12] Qi, R., Guo, R., Pan, T., Lin, R., Fu, C., & Liu, X. (2026). Enhancing spalling resistance and mechanical properties of ultra-high performance concrete at elevated temperatures using hybrid polyoxymethylene and steel fibers. Construction and Building Materials, 526, 146443. https://doi.org/10.1016/j.conbuildmat.2026.146443.
[13] Lee, K. J. L., Kevinly, C., & Tan, K. H. (2026). Effect of hybrid fibre on flexural behaviour and spalling resistance of ultra-high performance fibre-reinforced concrete at ambient and elevated temperatures. Construction and Building Materials, 517, 145670. https://doi.org/10.1016/j.conbuildmat.2026.145670.
[14] GB/T 50080-2016. (2016). Standard for test method of performance on ordinary fresh concrete.
[15] GB/T 31387-2015. (2015). Reactive powder concrete.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Scientific Journal of Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.






